As of June 1, Vryhof will no longer support the Internet Explorer 11 browser. For the best experience, please switch to a modern browser

Mooring
products

Filter

MOORLINK ANCHOR HANDLING SWIVELS

This ultra-short swivel range is designed with hexagonal geometry, reducing the risk for uncontrolled rolling onboard an anchor handler’s deck. The section is also shaped to reduce point loading whilst running over..

MOORLINK CHAIN CLAMPS

The MoorLink chain clamps are specially designed clamps developed to fit surface or sub-surface buoyancy to a mooring chain of any diameter.

MOORLINK FLOAT SWIVELS

MoorLink’s float swivel is used when large buoyancy is required to be fitted to a certified mooring leg. All MoorLink float swivels are approved by the Certifying Authorities.

MOORLINK INSTALLATION SWIVELS

MoorLink’s low friction installation swivels are designed to be used to reduce transfer of induced torque from an installation wire into the installed object, which could be subsea equipment, preset mooring systems..

MOORLINK M-LINKS

The M-Link concept is a proven concept developed by MoorLink as a cost enhanced alternative to connect polyester mooring lines. With the hollow pin design (pat. pending) we have managed to integrate..

MOORLINK MOORING CHAIN SWIVELS

The MoorLink mooring chain swivels are supplied in either forged or cast versions. The structural design is thoroughly analyzed by FEM-analysis and allows the swivel to run through a fairlead, chaser ring..

MOORLINK PIPE SWIVELS

MoorLink pipe swivels have been design with flexibility and cost optimization as main drivers. With a bulky and yet user friendly design, this tool is proving its value on offshore installation. Can..

MOORLINK U-LINKS & PEAR LINKS

MoorLink has produced a wide variety of U-links over the years and they come in numerous shapes and forms. U-links can be delivered for long term mooring and with cathodic protection.

MOORLINK WIRE CLAMPS

The MoorLink patented wire clamp is specially designed and developed to fit buoyancy (surface or sub-surface) to six stranded mooring wires. Each inlet is conical shaped avoiding bending damage to the mooring..

RigLOK

The RigLOK™ connector offers a secure and robust connection and disconnection method for mooring systems. Designed to meet the demands of drilling rig station keeping, the RigLOK™ is suitable for any temporary..

STEVADJUSTER®

The STEVADJUSTER® is an innovative, cost-effective and time-saving solution for chain adjustment, pre-tensioning of moorings and easy connection or disconnection of anchor lines. The entire operation takes place subsea and does not..

STEVIN®

The STEVIN® anchor was the original anchor design of Vryhof Anchors at its inception, outperforming all existing anchors at the time. Although initially designed for the dredging industry it has served numerous..

STEVMANTA® 

Marine operations related to offshore exploration and production are moving fast into deeper water, pushing the operational limit of existing equipment.

STEVPRIS®MK5 

Introduced in 1993, the STEVPRIS®Mk5 was the anchor the world was waiting for and very quickly became the most used drag anchor for larger mobile and permanent moorings, primarily because of its..

STEVPRIS®MK6

Due to their versatility STEVPRIS®Mk6 anchors serve a wide range of mooring applications. Although the large majority serves the mooring of offshore units such as drilling rigs, FPSO's and SPM buoys they..

STEVSHARK®

An adapted version of the STEVPRIS®Mk5, called STEVSHARK®, facilitates performance in hard soils such as limestone, calcarenite, very dense sands and coral.

STEVSHARK®REX

No anchor can deliver the holding power of the STEVSHARK®REX. The application of drag embedment anchors has been expanded to the most remote and challenging territories on earth.

STEVTENSIONER®

The proof loading of a permanent mooring system for CALM buoys and FPSOs is critical for a system’s certification. The proof loads are typically 80-100% of the design load so that substantial..